德国进口齿轮油泵

德国进口齿轮油泵 进口齿轮油泵厂家 进口齿轮油泵价格gear pumps

德国KAYSEN凯森进口齿轮油泵概述
本系列齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。齿轮油泵适用于输送不含固体颗粒和纤维，无腐蚀性，温度不高于80℃，粘度为5×10-6～1.5×10-3m2/s (5-00cSt)的润滑油或性质类似润滑油的其他液体。

主要特点：

1、齿轮油泵使用规定电压

线路电压不超过抽液泵铭牌上所规定电压的±10%方可使用。

2、齿轮油泵如何装备

开箱后按结构示意图装配，接上电动机

（1）并紧接连电机

（2）使之泵体与电机为一体

（3）上接好出水轮管

3、齿轮油泵使用前检查各部件外型完好才能开机使用。

4、齿轮油泵不宜作空运转，使用时，抽吸完毕，即停泵，否则会加速叶轮密封件轴承等磨损。也可能磨损泵管，因本泵电机空载转速可达10000转/分。

5、齿轮油泵及时调换电刷，电刷磨损到将不能使用时，须及时调换（2只电刷同时调换）否则会使电刷与换向器接触不良引起坏损，损坏换向器，严重时会烧坏电枢。

6、齿轮油泵在下列情况下不得使用，在使用过程中如发现绝缘损坏，电源线工电缆护套破裂，插头插座开裂或接触不良，以及断续运转，出现严惩火花等故障时，电机外壳操作时，应立即进行修理。在未修复前不得使用。

7、齿轮油泵防止过载，使用时，凡遇转速异常或降低时，应即停机检查是否有杂物卡住叶轮或电机是否发生故障，抽液泵因故刹车时必须立即切断电源

8、齿轮油泵使用工具要爱惜，所有抽涂泵要小心轻放避免受到冲击。

主要优点：

●齿轮经热处理有较高的硬度和强度，与轴一同安装在可更换的轴套内运转。泵内全部零件的润滑均在泵工作时利用输出介质而自动达到。

●泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力zui小，因此轴承负荷小，磨损小，泵效率高。

●泵设有安全阀作为超载保护，安全阀的全回流压力为泵额定排除压力的1.5倍，也可在允许排出压力范围内根据实际需要另外调整。但注意本安全阀不能作减压阀的*工作，需要时可在管路上另行安装。 从主轴外端向泵看，为顺时针旋转。

主要应用：

●在输油系统中可用作传输、增压泵

●在燃油系统中可用作输送、加压、喷射的燃油泵

●在一切工业领域中，均可作润滑油泵用

Germany KAYSEN imported gear pump overview
This series gear pump mainly gears, shaft, pump body, safety valve, shaft seal composed. Gear oil pump is suitable for conveying lubricating oil with no solid particles and fibers, no corrosion, temperature not higher than 80 ℃, viscosity of 5 × 10-6 ~ 1.5 × 10-3m2 / s (5-00cSt) or similar properties Other liquids of oil.

main feature:

1, gear pump using the specified voltage
The line voltage does not exceed ± 10% of the voltage specified on the pump nameplate.
2, gear pump how to equip
Out of the box after the structure of the assembly diagram, connected to the motor
(1) and immediay connected to the motor
(2) so that the pump body and the motor as a whole
(3) connected to a good water tube
3, gear pump before using the components to check the appearance of good start to use.
4, gear pump should not be empty operation, use, suction is completed, that is, stop the pump, otherwise it will accelerate the impeller seal bearing wear. May also wear pump tubing, because the pump motor no-load speed up to 10,000 r / min.
5, the gear pump timely exchange brush, brush wear will not be able to use, it is necessary to timely exchange (2 brush at the same time exchange) otherwise the brush and commutator bad contact caused damage, damage commutator, serious Will burn the armature.
6, the gear pump in the following circumstances shall not be used in the course of the use of insulation damage, power cord cable sheath rupture, plug socket cracking or poor contact, and intermittent operation, severe sparks and other failures, the motor shell operation Should be repaired immediay. Do not use before repair.
7, gear pump to prevent overload, when used, when the speed is abnormal or reduced, it should be shut down to check whether there is debris stuck impeller or motor failure, pumping pump brake must immediay cut off the power
8, gear pump use tools to cherish, all pumping pump to be careful to avoid the impact.

Key Benefits:

● The gears have a high hardness and strength by heat treatment and are installed in the replaceable sleeve with the shaft. All parts of the pump lubrication in the pump work with the output medium and automatically reached.
● The pump has a reasonable design of the drain and oil return tank, the gear in the work to withstand the minimum torque force, so the bearing load is small, wear small, high pump efficiency.
● The pump is equipped with a safety valve as overload protection. The full return pressure of the safety valve is 1.5 times of the rated pressure of the pump. It can also be adjusted according to the actual requirement in the allowable discharge pressure range. But pay attention to the safety valve can not be the long-term work of the valve, if necessary, can be installed on the pipeline. From the outer end of the spindle to the pump, for the clockwise rotation.

main application:

● In the oil system can be used as transmission, booster pump
● Fuel pump can be used in the fuel system for conveying, pressurizing and spraying
● In all industrial areas, can be used for lubricating oil pump

德国进口齿轮油泵 进口齿轮油泵厂家 进口齿轮油泵价格

德国KAYSEN凯森对您的承诺：

●放心的质量：从铸件到产品，实行全过程质量监控，*检测，责任到人！

●贴心的价格：高效成本控制，自产自销，减少中间环节，让利于客户！

●快速的货期：充足的库存，上海便捷物流，缩短交货期，严格按照合同期交货！

Germany Kaysen commitment to you:

● Reliable quality: from casting to the product, the implementation of the whole process of quality control, all-round detection, responsibility to the people!

● intimate price: efficient cost control, production for sale, to reduce the intermediate links, to help customers!

● fast delivery: adequate inventory, Shanghai convenient logistics, shorten the delivery time, in strict accordance with the contract delivery!

进口齿轮油泵厂家 进口齿轮油泵价格